Omnibus Environmental Health and Safety Plan for Chemistry
Originally Prepared March 1991
By the Chemistry Department Safety Committee
Paul T. Bonura, Chair, Anne Harmon, David Cocke, Arthur Bradberry
1.2 Definition of Responsibilities. 1
1.2.1 Chief Executive Officer. 1
1.2.2 Director of Risk Management 1
1.2.3 Chemistry Department Safety and Chemical Hygiene Officer. 2
1.2.4 Chemistry Department Hazardous Waste Officer. 3
1.2.6 Laboratory Coordinators. 4
1.3 Classification of Individuals Subject to the Plan. 5
1.3.1 Faculty, Research, Laboratory and/or Chemical Stockroom Workers. 5
1.3.2. Minimal Exposure Workers. 5
1.3.3 Class/Laboratory Workers. 5
1.3.4 Single/Limited Exposure Workers. 6
2.0 Safety and Hazardous Materials Plan. 7
2.1 Standard Operating Procedures. 7
2.1.3 Protective Clothing and Equipment 8
2.1.6 Chemical Purchase and Stockroom Control 11
2.1.7 Procedures for Storage of Chemicals. 12
2.1.8 Procedures for Chemical Wastes. 12
2.2 Procedure‑Specific Safety and Environmental Health Rules. 16
2.2.1 Procedures for Toxic Chemicals. 16
2.2.2 Procedures for Flammable Chemicals. 16
2.2.3 Procedures for Reactive Chemicals. 17
2.2.4 Procedures for Corrosive awl Contact‑Hazard Chemicals. 17
2.2.5 Procedures for High and Low Pressure Systems. 18
2.2.6 Procedures for Use of Radioactive Materials. 19
2.2.7 Procedures for Use of Instruments. 19
2.2.8 Procedures for Ionizing Radiation. 19
2.3.1 Definitions of Substances. 20
2.3.2 Designated Areas for Use of Inimical Chemicals. 20
2.3.3 Storage of Inimical Chemicals. 21
2.3.4 Personal Protective Equipment for Use of Inimical Chemicals. 21
2.4 Control Measures and Equipment 22
2.4.1 Eyewash Fountains and Safety Showers. 22
2.4.6 Flammable Liquid Storage. 24
2.4.7 Low Temperature Storage. 25
2.5 Violations of Plan Regulations. 26
2.5.1 Single Violation by a Single Individual or Multiple Individuals. 26
2.5.2 Repeated Violation by Multiple Individuals. 26
2.5.3 Repeated Violation by a Single Individual 26
2.5.4 Flagrant Violation of Safety and/or Hazard Rules. 27
3.1 Heating/Air Conditioning/Ventilation/Plumbing Failures. 28
3.3 Mechanical/Electrical Emergencies. 28
3.4.1 Events without Worker Contact 29
3.4.2 Events with Worker Contact 29
3.6 Declaration of Evacuation Emergency. 30
4.1 When Medical Consultation is Indicated. 32
4.2 Information Provided to Physician. 32
5.1 Workers Subject to Training Program... 34
5.2 The Safety and Environmental Health Training Program... 34
5.2.4 Transport of Chemicals. 35
5.2.5 Storage of Chemicals. 35
5.2.7 Teaching Laboratories. 36
Safety and Environmental Health Officers. 39
Checklist for Student End of Lab Research Work. 42
Hazardous Waste from Nonspecific Sources. 45
Discarded Commercial Chemical Products, Off Specification Species, 48
Container Residuals, and Spill Residues Thereof ‑ Acute Hazardous Waste. 48
The goal in establishing this plan and its associated regulation is to minimize the exposure of workers within the Chemistry Department to chemical and physical hazards associated with their employment or educational activities. It is also to ensure that chemical materials originating within the Chemistry Department do not become a environmental hazard to the community at large. To achieve this end goal, this document institutes work area safety and chemical exposure standards, regulates the maintenance and performance level of safety equipment, mandates waste handling rules, establishes the policy of providing information and training of workers, and documents responsibilities for tile management for the plan. This plan incorporates elements of federal and state law governing chemical hygiene, right to know, chemical waste management, and institutional safety.
1.2 Definition of Responsibilities
This section defines the responsibilities of various officials for the implementation and operation of this plan. A list of the names of those individuals will be prepared by the Director of Safety and Environmental Health each academic year and approved by the Chief Executive Officer of the university. Any changes in university and departmental officials and their areas of responsibility will be disseminated to faculty and staff and will be distributed to employees of the Chemistry Department as part of the yearly safety and chemical hygiene training program.
The Chief Executive Officer, (University President), has ultimate responsibility for chemical hygiene and safety within the university. The responsibilities of tile Chief Executive Officer include:
1. With other administrators, provide for the continuing support for institutional safety, chemical hygiene and hazardous waste handling.
1.3.2 Director of Risk Management
The Director of Risk Management has primary responsibility for reviewing the specific procedures involved in the Safety and Environmental Health Plan for compliance with federal state and local laws and regulations. The responsibilities of the Director include:
1. Oversight and coordination of activities and responsibilities of the Facilities Maintenance Department with the individual departments, to install and maintain safety and chemical hygiene equipment (such as fume hoods, power lines, fire detection equipment, etc).
2. Oversight and coordination of activities and responsibilities of the Shipping and Receiving Office to ensure the proper handling of incoming hazardous materials.
3. Coordination and supervision of the training mandated by the plan with the department.
4. Coordination and supervision of the inspection of university facilities to ascertain the level of compliance with the plan.
5. Maintain knowledge of the current legal requirements for maintenance of safety equipment, for regulated substances, and for required chemical hygiene equipment and transmission of such knowledge as needed to the department or individual employees.
6. Establish and maintain an accurate record of:
a. Measurements taken to monitor employee exposures, and any medical consultations and examinations including written opinions required by this standard.
b. Reports of accidents and emergencies, including remedial actions taken.
c. Review records of the examination and repair of safety and environmental health equipment, such as fire alarms and equipment, ventilation equipment, and other equipment maintained by the Facilities Maintenance Department..
d. Records of safety and environmental health inspections and drills.
e. A file of suggestions for changes and improvements to the plan, and reference literature for safety and chemical hygiene, including this plan.
1.3.3 Chemistry Department Safety and Chemical Hygiene Officer
The Departmental Safety and Chemical Hygiene Officer (Department Chair or Designate, acting as an Additional Duty Safety Officer (ADSO)), in conjunction with the Department Chair and the University Director of Risk Management, is responsible for establishing chemical hygiene and safety procedures within the department. This individual may be the same person as the Departmental Hazardous Waste Officer. This individual will:
1. Coordinate with the Director of Risk Management the safety and chemical hygiene related activities within the department, including, , the employee training program mandated by the plan.
2. Determine the required levels of protective apparel and equipment needed in the department, and oversee the maintenance of safety and chemical hygiene equipment within the department.
3. Coordinate the inspection of safety, hygiene, housekeeping and emergency equipment in the department to ascertain the level of compliance with the plan. This includes an official inspection, no less frequently than annually, of every area within the governance of the Chemistry Department, and any other mandated inspections.
4. Maintain knowledge of the current legal requirements for maintenance of safety equipment, for regulated substances, and for required chemical hygiene equipment and transmission of such knowledge as needed to the department, area supervisors, or individual employees.
5. Establish and maintain an accurate record of:
a. Any measurements taken to monitor employee exposures, and any medical consultations and examinations including written opinions required by this standard.
b. Reports of accidents and emergencies, including remedial actions taken.
c. The departmental file of MSDSs and reference literature for safety and chemical hygiene, including this plan.
1.3.4 Chemistry Department Hazardous Waste Officer
The Departmental Hazardous Waste Officer, (Department Chair or Designate) is responsible, in coordination with the University Director of Risk Management for the proper handling and disposal of hazardous wastes generated in the activities of the department. This individual will:
a. A cumulative record of waste generated and accumulated in the Department since the last disposal.
b. Such department wide chemical and hazardous materials inventory as may be required.
The Area Supervisor is responsible for safety and environmental health within a designated area, (typically an individual room), or the activities of workers under the area supervisor's control. Coordinators of each specific laboratory course are to be considered the area supervisor for that course. For research laboratories, the senior faculty member overseeing the research will be the Area Supervisor. The Area Supervisor will:
a. Any measurements taken to monitor employee exposures, and any medical consultations and examinations including written opinions required by standards of good practice.
b. Reports of accidents and emergencies, including remedial actions taken.
c. Required annual Hazardous Communication training for all students and employees working in their area.
Laboratory Coordinators fall into a special category of Area Supervisors. They are the individual faculty who dictate policy and procedure for a particular laboratory course. To ensure the safety and chemical hygiene of the students the laboratory coordinator will perform the following duties beyond those of the Area Supervisors.
1.3 Classification of Individuals Subject to the Plan
The persons potentially subject to this document will be classed in one of four groups. Those grouping are
1.3.1 Faculty, Research, Laboratory and/or Chemical Stockroom Workers
Defined as those individuals working in the stock and laboratory preparation rooms, acting as teaching assistants, performing postgraduate research work, or taking part in a laboratory educational experience that does not have a classroom component. Such individuals will be responsible for the following:
1.3.2 Minimal Exposure Workers
Defined as office and custodial workers who may as part of their duties be required to enter a laboratory or storage area, who will perform no manipulations of hazardous chemicals or equipment within that area. Assuming that the responsibilities placed on other workers are met, the potential for exposure to chemical hazards or mechanical hazards for such individuals should be minimal. Based on this knowledge, such workers will be provided a special training course that focuses on the recognition of potential hazard conditions and emergency procedures. These workers should not attempt to perform their duties in areas in which safety and health rules are being violated, but should report such conditions to the appropriate area supervisor.
1.3.3 Class/Laboratory Workers
Defined as students in lecture/laboratory educational programs that have both classroom and laboratory component. Such individuals will be responsible for the following:
1.3.4 Single/Limited Exposure Workers
Classified as workers such as maintenance and repair personnel who may be required to enter and work in a laboratory or storage area. Such workers should obtain authorization from the Area Supervisor or the Departmental Safety and Chemical Hygiene Officer, who will normally accompany the individual into the work area and verify, or arrange for some other qualified person to verify that the work area is cleared or any potential hazard to the worker.
2.0 Safety and Hazardous Materials Plan
2.1 Standard Operating Procedures
For the chemicals they work with, all workers should know and be constantly aware of the following:
Workers must obtain prior approval from the area supervisor to proceed with a laboratory task whenever:
1. A new or unfamiliar laboratory procedure or test is to be carried out.
2. It is likely that the toxic limit concentration for a chemical involved in the process could be exceeded or that other harm is likely.
3. There is a change in a procedure or test, even if it is very similar to prior practices. "Change in a procedure or test" means:
a. A 10% or greater increase or decrease in the amount of one or more chemicals used.
b. A substitution or deletion of any of the chemicals in a procedure.
c. Any change in other conditions under which the procedure is to be conducted.
4. There is a failure of any of the equipment used in a process, in particular safeguards such as fume hoods or clamped apparatus.
5. An unexpected result has been experienced on a previous attempt of the procedure.
6. Members of the laboratory staff become ill due to a possible chemical exposure, suspect that they or others have been exposed to a hazardous material, or otherwise suspect a failure of any safeguards.
a. Only Area Supervisors may order chemicals. This approval is in addition to any budgetary approval that may be necessary. Prior to orders for purchase the area supervisor must determine if any supplies of the chemical are currently in the departmental store room.
b.The Area Supervisor should determine before ordering chemicals the requirements for protective equipment and handling of the chemical, and ensure that any needed equipment is available.
c. Only the minimum amount of chemicals needed should be ordered, to ensure that large amounts of unused chemicals do not accumulate within the department. Large quantities of chemicals in excess of predicted requirements should not be purchased because the unit price is thereby reduced. Such excess chemicals will usually have to be disposed of as hazardous waste at significant cost.
2. Receipt of Chemicals:
a. The Chemistry Department stockroom personnel will remove all chemicals from their shipping containers, mark the receipt date. If the chemical has a known shelf life this expiration date should be noted on a separate tag on the container. (Unopened diethylether containers should not be kept for more than six months unless packed under nitrogen or other inert gas in sealed containers. Diethylether should not be kept for over one month after the container is initially opened.)
b. Shipments may not be picked up by the ordering individual until they have been authorized for pickup by the laboratory manager.
c. MSDSs should be reviewed by the worker using the chemical, and the Area Supervisor and then added to the departmental MSDS file if they are not already on record. If an MSDS is not available in the Department, and the chemical arrives in advance of the MSDS from the supplier, an MSDS should be located on the Internet before a chemical is used.
3. Transport of Chemicals:
a. All toxic, reactive or hazardous chemicals must be transported within the halls in the chemistry building on an approved cart or in an approved chemical transport bucket.
b. All transported chemicals must have a secure fitting cap on the container. Gas cylinders must be capped when moved even within laboratories.
c. Chemicals should not be transported via stairwells, or the passenger elevator unless absolutely necessary. The dumb waiter or, if necessary, the elevator without people in it should be used to transfer chemicals from floor to floor.
Storage of chemicals in a laboratory is an issue largely under the control of the Area Supervisors. There are several regulations that apply, however, that workers must be aware of. These rules are:
I. Classification of Wastes: Wastes must be initially classified as hazardous or nonhazardous. Hazardous wastes are those defined by the United States Occupational Safety and Health Administration (OSHA) as a substance for which there is statistically significant evidence, based on at least one scientific study, showing that acute or chronic harm may result from exposure to that chemical. This is regardless of whether the handling of the material is proper or improper.
a. Nonhazardous waste: Wastes that meet none of the criteria of hazardous wastes may be considered as nonhazardous. Following certification of a waste as nonhazardous it may be treated as general garbage. Is important however that the waste be certified first.
i. Disposal of Nonhazardous Wastes: With the exception of glass wastes the Chemistry Department makes no rules regarding the landfill disposal of nonhazardous wastes. The City of Beaumont does regulate what wastes may be disposed of in the public sewers. Some of these rules are more stringent than the criteria for classification of a waste as hazardous. Based on these rules nonhazardous wastes that do not meet the following requirements may not be disposed of in the sewer lines.
(i) Any fat, oil, grease, ash, cinder, sand, mud, shavings, metal, glass, tar or other solid or viscous liquid substance which may cause obstruction to the flow in sewer of other interferences with the proper operation of the wastewater treatment system.
(ii) Any liquid or vapor having a flash point temperature higher than 650C (1500F).
(iii) Any wastewater with a pH less than 6.0 or above 11.0 or having any corrosive property capable of causing damage or hazard to structures, equipment, or personnel of the wastewater treatment system.
(iv) Any waste or water containing suspended or undissolved solids of such character that unusual attention or expense is required to handle such material.
(v) Any water with objectionable color.
b. Hazardous waste: A waste is hazardous if it fits into one of the following categories:
i. Listed Waste: A listed waste is one included in one of four lists, generated by the United States Environmental Protection Agency (EPA), Identified by the letters F, K, P, and U. Within the lists the materials are assigned hazardous waste numbers and hazard rating by the EPA. The ratings systems and the lists *are provided in appendix. The definitions for the list types are as follows:
(i) Type F wastes are generic categories of solvents and wastes and wastewater from some specific processes.
(ii) Type K wastes are hazardous wastes from specific sources.
(iii) Type P wastes include acutely hazardous wastes.
(iv) Type U wastes are specific commercial chemical products, chemical intermediates and off specification chemical products.
b Characteristic Waste: If a waste is not found to be one of the Listed Wastes it may be an "unknown" waste, which must be tested to determine the nature of the waste properties or characteristics. The Characteristics to be evaluated are:
(i) Ignitability (Waste #D001): Any easily combustible or flammable liquid with a flash point less than 600 C (1400 F), or solid that burns easily.
(ii) Corrosive (Waste #D002): Any waste that dissolves metals or other materials or burns the skin, pH less than 2 or greater than 12.5.
(iii) Reactivity (Waste #D003): Wastes which are unstable, release toxic gases, or undergo rapid or violent chemical reaction with water or other materials.
(iv) EP Toxicity (Waste #s D004‑D017): Extracts of the material contain high concentrations of heavy metals and/or specific pesticides that could be released into ground water. Appendix 4 contains the list of the contaminates and their maximum allowed concentrations to exempt from EPA Toxic designation.
5. Hazardous Waste Accumulation and Storage: As waste is classified it must be accumulated and stored until it can be disposed of. The following rules should be applied to the accumulation and storage of materials classified as hazardous waste:
a. Hazardous wastes of differing classifications or physical properties should be kept in separate closed containers, as should wastes that are incompatible with one another. This will require that aqueous and organic wastes be separated. Halogenated and non-halogenated organic wastes must also be kept separate from one another.
b. Hazardous wastes must be stored in closed containers that can be sealed and are not subject to decomposition by the contents.
i. Aqueous hazardous waste solutions should not be stored in metal drums. If of greater than pH of 8 such wastes should not be stored in glass containers.
ii. Organic hazardous wastes should be accumulated and stored in containers which do not contain polymer components that may be structurally weaken by exposure to the wastes.
iii. Leave 2 inches empty at the top of each container of liquid. Do not use wide moth containers for liquids.
c. All hazardous waste containers must be labeled with the following information:
i. Once hazardous wastes have been introduced to a accumulation and storage container the date must be noted on the container and the container must be removed from the laboratory to a designated storage area at the end of a 30 day period.d. Waste must be removed from the laboratory to the stock room when containers are full or there is no expectation of any further wastes of the type in the container. Waste from teaching laboratories must be removed when all sections have completed the particular experiment that produces the waste. An exception to this exists where halogenated and non-halogenated organic solvent wastes produced in successive experiments are collected separately in larger containers. Such containers should be removed at the end of the semester.
e. Transport of waste must be done following the rules for the transport of any chemical material. (See section 2.1.6)
2.1 The chemistry department makes special exception regarding glass waste, in the disposal of materials into the general trash. Clean glass wastes, particularly broken glass, should be kept separate from the general garbage to avoid potential safety hazards to custodians. Specific glass containers will be made available in each laboratory area for the disposal of glass waste. Thermometers that are broken and their pieces may contain small amounts of mercury and should be placed in a separate labeled container from other glass.
2.2 Procedure‑Specific Safety and Environmental Health Rules
All routine or repeated laboratory procedures must contain a written description of the specific safety practices, incorporating the applicable precautions, described in this section. Workers should read and understand these practices before commencing a procedure.
2.2.1 Procedures for Toxic Chemicals
The MSDSs for many of the chemicals used in the laboratory will state recommended limits or OSHA‑mandated limits, or both, as guidelines for exposure. Typical limits arc threshold limit values (TLV), permissible exposure limits (PEL), and action levels. When such limits are stated, they should be used to assist the Area Supervisor and chemical user in determining the safety precautions, control measures, and safety apparel that are required when working a toxic chemical.
1. When a TLV or PEL value is less than 50 ppm or 100 mg/m3 the application of the chemical must occur in an operating fume hood, glove box, vacuum line, or similar device, which is equipped with appropriate traps and/or scrubbers. If none are available, no work should be performed using that chemical. If utilized, the concentration within the laboratory of such a chemical must be measured to ensure that exposure limits are not exceeded. Records of such measurements must by maintained by both the Area Supervisor and Departmental Safety and Chemical Hygiene Officer, measures above the allowed concentration must be reported to the workers involved. Such data should be incorporated in the yearly plan review.
2. If a TLV, PEL, or comparable value is not available for a substance, the animal or human median inhalation lethal concentration information, LC50, will be assessed. If that value is less than 200 ppm or 2000 mg/m3 (when administered continuously for one hour or less), then the chemical must be used in an operating fume hood, glove box, vacuum line, or similar device, which is equipped with appropriate traps and/or scrubbers. If none are available, no work should be performed using that chemical. If utilized, the concentration in the laboratory of such chemicals must be measured to ensure that exposure limits are not exceeded. Records of such measurements must by maintained by both the Area Supervisor and Departmental Safety and Hazardous Materials Officer, measures above the allowed concentration must be reported to the workers involved. Such data should be incorporated in the yearly plan review.
3. Whenever laboratory handling of toxic substances with moderate or, greater vapor pressures will be likely to exceed acceptable air concentration limits, laboratory work with such liquids and solids will be conducted in a fume hood, glove box, vacuum line, or similar device, which is equipped with appropriate traps and/or scrubbers. If none are available, no work should be performed using that chemical.
2.2.2 Procedures for Flammable Chemicals
In general, the flammability of a chemical is determined by its flash point, the lowest temperature at which an ignition source can cause the chemical to ignite momentarily under certain controlled conditions. Information of flash points is available in MSDSs for purchased chemicals.
2.2.3 Procedures for Reactive Chemicals
a. A reactive chemical is one that meets one or more of the following criteria:
b. Is described as such in the current edition of "Handbook of Reactive Chemical Hazards" by L. Bretherick or other authoritative source, is indicated to be reactive in the MSDS or on the label,
c. Is ranked by the NFPA as 3 or 4 for reactivity,
d. Is identified by the United States Department of Transportation (DOT) as:
i. An oxidizer,
ii. An organic peroxide, or
iii. An explosive, Class A, B, or C,
e. Meets the EPA definition of reactive in 40 CFR 261.23
f. Meets the OSHA definition of unstable in 29 CFR 1910.1450
g. Is known or found to be reactive (will vigorously polymerize, decompose, condense, will become self‑reactive under conditions of shock, pressure or temperature, or reacts with water to release a gas that is either flammable or presents a health hazard) with other substances.
h. Handle reactive chemicals with all proper safety precautions, including segregation in storage and prohibition on mixing even small quantities with other chemicals without prior approval and appropriate personal protection and precautions. Also be aware of time limits and conditions for the storage of reactive chemicals and use them up or dispose of then as required. (Opened cans of diethyl ether should not be kept for more than one month)
2.2.4 Procedures for Corrosive awl Contact‑Hazard Chemicals
a. Is listed as such on the MSDS or the label,
b. Fits the OSHA definition of corrosive in Appendix A of 29 CFR 1910.1200,
c. Fits the EPA definition of corrosive in 40 CFR 261.22 (has a pH greater than 12 or less than 2.5),
d. Is known or found to be corrosive to living tissue.
2. A contact hazard chemical is an allergen or sensitizer that:
a. Is so identified in the MSDS or on the label,
b. Is so identified or described in the medical or industrial hygiene literature, or
c. Is known or found to be an allergen or sensitizer.
3. Handle corrosive chemicals with all proper safety precautions, including wearing safety glass or goggles and a face shield (see section 2.1.3 (1)), gloves tested for the absence of pin holes and known to be resistant to permeation or penetration, and a laboratory apron or laboratory coat.
2.2.5 Procedures for High and Low Pressure Systems
2.2.6 Procedures for Use of Radioactive Materials
Procedures and rules governing the use of radioactive materials are promulgated by the University Radiation Safety Officer for Radioactive Materials, currently Dr. George Irwin, and are included in the University's Radiation Safety Manual. Prior approval from Dr. Irwin is required before any use of Radioactive Materials can be allowed. Note that the Radioactive Materials License issued by the Texas Department of State Health Services covers items such as the source in the electron capture detectors in some gas chromatographs in the Department. Access to and use of these gas chromatographs is limited to those properly authorized under the rules contained in the Radiation Safety Manual.
2.2.7 Procedures for Use of Instruments
Specific instruments, either due to their expense to the department or to the potential hazard to users, will be assigned a specific Area Supervisor or Supervisors. Workers must seek and obtain the approval of the appropriate Area Supervisor to use these instruments. The Area Supervisor will keep records of the name of approved users.
2.2.8 Procedures for Ionizing Radiation
No ionizing radiation machines (as defined by the Texas Department of State Health Services, but see 2.2.6 above) are currently in use in the Chemistry Department. Rules regulating ionizing radiation producing machines elsewhere in the University are promulgated by the Radiation Safety Officer for ionizing radiation machines, currently Dr. David Cocke.
2.1 Procedures for Substances with a High or Unknown Degree of Acute Toxicity, Carcinogens, and Reproductive Toxins
The procedures in this section must be followed when working with more than 10 mg. of any carcinogen, reproductive toxin, substance that has a high degree of acute toxicity, or a chemical whose toxic properties are unknown.
2.3.1 Definitions of Substances
For the purposes of the "Chemical Hygiene Plan" the compounds in these categories will be called "inimical". The following definitions apply to these compounds:
a. Is regulated as a carcinogen by OSHA; or
b. Is listed under the category "known to be carcinogens" in the latest edition of the Annual Report on Carcinogens published by the National Toxicology Program (NTP); or
c. Is listed under Group I ("carcinogenic to humans") in the latest edition by the International Agency for Research on Cancer Monographs (IARC); or
d. Is listed in either Group 2A or 2B by IARC or under the category, reasonably anticipated to be carcinogens" by NTP, and causes statistically significant tumor incidence in experimental animals in accordance with any of the following criteria:
i. After inhalation exposure of 6‑7 hours per day, 5 days per week, for a significant portion of a lifetime to dosages of less than 10 mg/m3;
ii. After repeated skin application of less than 300 mg/kg of body weight per week, or
iii. After oral dosages of less than 50 mg/kg of body weight per day.
2. Reproductive Toxin: Any substance described as such in an applicable MSDS or any chemical that has been shown to affect the reproductive capabilities including chromosomal damage (mutations) and effects on a fetus (teratogenesis).
3. Substance with a high degree or acute toxicity: Any substance for which the LD50 data described in the applicable MSDS cause the substance to be classified as a "highly toxic chemical" as defined in ANSI Z129.1.
4. Chemical whose toxic properties are unknown but may reasonably be expected to fall into the classes described in 1 through 3 above by virtue of it structure and/or functional groups and/or analogy with substances known to be inimical chemicals: A chemical for which there is no ' known statistically significant study conducted in accordance with established scientific principles that established its toxicity, but resembles in any way, a substance known to be an inimical chemical.
2.3.2 Designated Areas for Use of Inimical Chemicals
Inimical chemicals must be used in a designated area. A designated area may be a fume hood, glove box, portion of a laboratory, or an entire laboratory designated as the only area where work with quantities of the inimical chemical in excess of a specific limit shall be conducted. Such areas shall be posted with their boundaries clearly marked. Only persons trained to work with inimical chemicals will work with those chemicals in the designated area. Such persons will:
2.3.3 Storage of Inimical Chemicals
Inimical chemicals must be stored in locked and enclosed spaces ideally with a slight negative pressure relative to the building and room pressure.
2.3.4 Personal Protective Equipment for Use of Inimical Chemicals
When handling inimical chemicals, workers must wear long‑sleeved disposable clothing and gloves known to resist permeation by the inimical chemicals to be used when working in designated areas.
2.2 Control Measures and Equipment
2.4.1 Eyewash Fountains and Safety Showers
a. Laboratory ventilation should be maintained to meet the design specifications for the building. Shortcomings detected by the Energy Management System should be promptly rectified. The general air flow should be uniform throughout the laboratory. This flow is not necessarily sufficient to prevent accumulation of chemical vapors in the laboratory.
b. Work with toxic chemicals that have low air concentration limits, or that have high vapor pressures, should always be done carried out in a fume hood, vacuum line or glove box.
c. Alterations to the ventilation system must only be performed by Facilities Maintenance personnel or contractors specifically tasked to make such alterations and must be tested to ensure that room ventilation has not suffered.
a. A fume hood with a minimum of 2.5 linear feet of hood space per person should be provided for every two workers if they spend most of their time working with chemicals. While this is a minimum space, some laboratories in which works will spent virtually all time working in the fume hood space requirements are double of more of the above figure.
b. Fume hoods should provide a minimum of 80 to 100 linear feet per minute of air flow regardless of door position.
c. Each fume hood should have a continuous monitoring device to allow convenient confirmation of adequate hood performance before and during use. The airflow in each hood in the Chemistry building is continuously monitored remotely by the Energy Management System.
d. The fume hood ventilation monitors should be tested and recalibrated if necessary annually or more often if needed to ensure the systems is working up to standard. Testing reports will be maintained in the Facilities Management Work Order System.
e. A fume hood is a safety backup for condensers, traps, or other devices that collect vapors and fumes. It is not to be used to "dispose" of chemicals by evaporation unless the vapors are trapped and recovered for proper disposal
f. Apparatus inside a hood should be placed on the floor of the hood at least six inches from the front edge.
g. Fume hood "doors" should be closed at least to the mark indicated on the hood door at all times except when necessary to adjust the apparatus that is inside the hood.
h. The hood fan should be "on" whenever a chemical is inside the hood, whether or not any work is being done in the hood. All hoods in the Chemistry Building are now designed to run continuously as part of the building air handling system, and the fan is not under the control of the worker, excepting the ability to activate the emergency purge mode. This increased the fan motor speed and hence increases the airflow. The emergency purge must not be activated unless necessary, as it disrupts the operation of the building ventilation system. Workers should be aware that activation of the fire alarm will, in compliance with the requirements of the Life Safety Code, shut off all fans in the building.
i. Workers should be aware of the steps that will be required in the event that a power or hood failure should occur.
j. Hood vents, ducts, and fans will be inspected once each three months to be sure that they are clean and clear of obstructions. If a fume hood is found to not be working properly it should be labeled and a report 'made to the appropriate Area Supervisor.
k. Hoods are not to be used as storage areas for chemicals, apparatus or other materials.
2.4.6 Flammable Liquid Storage
a. Never disable the spring‑loaded closure.
b. Always keep the flame‑arrestor screen in place; replace if punctured or damaged.
2. Fire hazard chemicals should be stored in appropriately designed and labeled cabinets. Cabinets designed for the storage of flammable materials should be properly used and maintained. Read and follow the manufacturer's information and follow the following safety practices:
a. Store only compatible materials inside a cabinet.
b. Do not store paper or cardboard or other combustible packaging material in a flammable‑liquid storage cabinet.
c. The manufacturer establishes quantity limits for various sizes of flammable‑liquid storage cabinets; do not overload a cabinet.
2.3 Violations of Plan Regulations
In as much as these regulations are based on an interest in the safety of workers and legal requirements it is a necessity that there be a penalty phase, short of legal action, to underscore the seriousness of regulations and required practices promulgated in this plan. It is the desire of the University and Chemistry Department to encourage and require compliance before harm comes to the worker or the environment through unsafe action. With this in mind the following series of recourse actions is available to the safety and hazardous materials officials.
2.5.1 Single Violation by a Single Individual or Multiple Individuals
Such violations will be dealt with by the Area Supervisor who will discuss with the individual or group of individuals the nature of the violation and determine if the fault lies in a communication breakdown or individual irresponsibility.
2.5.2 Repeated Violation by Multiple Individuals
Such violations will be dealt with by a review of the situation. Review will be made by the Area Supervisors involved and the appropriate departmental officer to:
4. Determine if mandated exposure limits have been exceeded and perform the any required duties, (offer of medical examinations, report to university Director of Risk Management, etc).
2.5.3 Repeated Violation by a Single Individual
Such violations will be dealt with by a reviewed two Area Supervisors from the department and the appropriate departmental officer to:
2.5.4 Flagrant Violation of Safety and/or Hazard Rules
Such violations are those that result in the injury of workers or gross environmental damage must be dealt with immediately by a meeting of all Chemistry Department Area Supervisors, the appropriate departmental officer and the Director of Risk Management to ascertain the level of severity of the violation and the action to be taken against the individual and/or the Area Supervisor involved. Actions may range from the issue of a warning, to penalty, to dismissal of the worker. A complete report will be prepared on the incident and its outcome by the departmental officer.
If a worker terminates his/her relationship, either as student or employee, with the Chemistry Department, the worker must see to the successful completion of their "Check Out" sheet. If wastes are not labeled and disposed of or other areas not left in proper order, the Chemistry Department through the appropriate Area Supervisors will get things in order, but the costs associated with such effort will be calculated and the information submitted to the University administration for legal review with a view to billing the former worker. Until any outstanding amounts are paid the university will withhold transcript and other similar documents from the worker.
Work within the laboratory and stockrooms require that great care be taken to avoid hazardous situations. In the event that, despite all efforts to avoid them, emergency situations should occur workers must be aware of their role and duties to minimize the danger to themselves and others.
3.1 Heating/Air Conditioning/Ventilation/Plumbing Failures
In the case of a localized outage, such as a single outlet or room the Area Supervisor should be contacted. In the event of a building wide or area wide ~ power outage emergency lighting should come on to ensure the safe evacuation of the laboratory or stockroom. To avoid hazards during and after the power failure, workers should take the following precautions.
3.3 Mechanical/Electrical Emergencies
These events may or may not involve workers, but do not involve hazardous chemicals.
These emergencies will be classified as those that involve exposure or potential exposure to chemicals, regardless of whether or not as the primary or secondary effect of the incident.
3.4.1 Events without Worker Contact
These events would be those such as spills of hazardous chemical compounds in which the worker has had no exposure to the material. The worker should follow the following protocol:
3.4.2 Events with Worker Contact
These events would be those that involve the exposure of workers to hazardous chemicals. It is noted that workers should be familiar with the MSDS for the compounds they use and therefore should be aware to the treatment for exposure to the chemical. The worker should seek the aid of laboratory partners immediately to remove and treat the effects of the exposure. The general protocol for treatment of chemical exposures should be:
Fire emergencies can quickly get out of hand. Action must be taken rapidly. The evaluation of MSDS reports prior to beginning work should inform workers of the potential for fire and the type of apparatus to be used to extinguish any fire. In the event of a fire the worker should ensure that the University Police are called on 8311 and advised of the fire and its location (room number). To the extent that the worker is able without risk to him or herself, (s)he should:
a. Small fires may be suffocated by covering with an inverted beaker.
b. Larger fires may require suffocation with the appropriate fire extinguisher or sand, in the case of metal of some reactive chemical reagents.
2. If a fire becomes out of control, the fire alarm should be sounded, the laboratory doors closed, but not locked, and building evacuated. The building must be evacuated because activating the fire alarm shuts off all ventilation in the building. Workers should assemble in the designated area outside the building on the Women's Gym side..
3. Workers involved in fires regardless of size should prepare a written report for the Area Supervisor who will review the events with the Departmental Director of Safety and Chemical Hygiene. The review of the event will be made part of the yearly review.
3.6 Declaration of Evacuation Emergency
In the event of an out of control fire emergency or chemical emergency it may be necessary to evacuate the building to ensure the safety of those within the building. This must not be done frivolously, but it is important that the call to evacuate be done rapidly before harm may come to workers. The building must be evacuated in the following situations:
To call to evacuate the building one need only activate the fire alarm system. In the event that the cause of the evacuation emergency is a chemical spill the person who sent the alarm should contact the University Police on 8311 to confirm the chemical nature of the incident.
At the time of evacuation each worker, to the extent practical and safe, should turn off all equipment and secure all laboratories before leaving. The workers should assemble outside the building in the assigned area so that Area Supervisors may determine if all workers have evacuated the building.
The Director of Risk Management will monitor the schedule of alarm and detector testing to ensure the operation of these safety devices.
4.1 When Medical Consultation is Indicated
Workers must have access to medical consultation, performed by or under the direct supervision of a licensed physician, at a reasonable time and place, without loss of pay and shall be without cost to the worker. In the case of employees, including student employees, the provisions and requirements of the applicable Workers' Compensation statutes and regulations will apply. Workers have the right to decline any medical evaluation or treatment and have a right to select the health care provider of their choosing. Workers' Compensation procedures include provisions that will pay for initial evaluation and/or emergency care regardless of the provider or facility. However, the Workers' Compensation system will only pay follow-up evaluation and treatment, in accordance with the applicable statutes and regulations. Medical consultation is indicated if:
2. An action level, or PEL for any chemical is exceeded o multiple occasions and there is a substance specific standard established.
4.2 Information Provided to Physician
The physician must, to the maximum extent practical, be provided with the following information:
For consultation or examination required under this plan, the Area Supervisor will, to the extent permissible under the various privacy statutes, obtain from the examining physician a written opinion or copies of reports containing such opinions. A report of the incident will be placed on file with the Director of Risk Management with copies on file in the Department. In the case of employees, any medical records or opinions will be filed in the Workers' Compensation Records in the Human Resources Department. In the case of students who are not employees, any medical records or opinions will be maintained by the Division of Student Affairs or placed in the Confidential Section of the Student's Permanent University Record. Copies of available medical reports and opinions may be used internally by the Office of Risk Management in investigating the cause.
Any medical opinion should include, to the extent legally permissible:
3. Any medical condition which may be revealed in the course of the examination which may place the worker at increased risk as a result of exposure to a hazardous chemical utilized in the work area; and
To ensure that each worker within the department has obtained an adequate level of understanding, knowledge and appreciation of the responsibilities and demands placed upon them by the legal requirements of safety, chemical hygiene and waste regulations the following formal training program will be presented each year. Area Super visors will also supplement this training with process specific training to workers in their areas.
5.1 Workers Subject to Training Program
All individuals who receive employment through the Chemistry Department must attend a training program based on their classification within this Plan. (See Section 1.3)
5.2 The Safety and Environmental Health Training Program
This aspect of this plan is designed to provide an outline of topics that should be covered in the training program. The specifics of the presentation are left the University Director of Risk Management and the Departmental Directors of Safety and Chemical Hygiene and Hazardous Materials. The training will be designed to meet the requirements of the Texas Hazard Communication Act and the University Hazard Communication Plan. Much of the training will be provided by the appropriate area supervisors and will often be customized to address the specific situation and circumstances in which the worker will be working. The following will be communicated and/or made available to each worker:
All information resources (laws, applicable governmental regulations, MSDSs, a copy of the current plan, the yearly review and other literature) utilized to generate and maintain the Hazard Communication Plan will be available within the Chemistry Department from the Departmental Safety and Chemical Hygiene Officer.
Due to ‑the large variety of processes and chemicals used in the department much of the burden for specific safety and environmental health training will fall to the individual Area Supervisors. Area Supervisors should seek the assistance if needed of the Departmental Safety and Chemical Hygiene and Hazardous Materials Directors. The Directors should seek out the Area Supervisors to ensure that they are up to date on the regulations and allowed exposure limits they and workers under their control utilize. Specifically, Area Supervisors should make their work aware of:
The plan and other associated plans will be reviewed annually by the Director of Risk Management, the Chair of the Department of Chemistry and Physics, the Departmental Safety and Chemical Hygiene Officer and the Hazardous Waste Coordinator Officer. This group should review the following information.
Safety and Environmental Health Officers
Chief Executive Officer Dr. James Simmons
President, 91制片厂
100 Plummer Building
P.O. Box 10001
Ext. 8405
University Director of Risk Management Dr. John A. Whittle
O-95 Maes Building
P.O. Box 10807
Ext. 8276
Chair, Dept of Chemistry and Physics Dr. Keith C. Hansen
121G Chemistry Building
P.O. Box 10022
Ext. 8266
Chemistry Dept. Hazardous Waste Coordinator Mr. Arthur Bradberry
112 Chemistry Building
P.O. Box 10022
Ext.8279
Chemistry Dept. Safety and
Chemical Hygiene Officer Ms. Marsha Williams
121J Chemistry Building
P.O. Box 10022
Ext. 8273
Student Lab Safety Rules
Safety Regulations for Chemistry Department Teaching Laboratories
I have read the above safety rules and will observe them in this chemistry course. I have also made myself familiar with the position and operation of the fire extinguisher, safety shower and eye wash in the laboratory.
Course Name :
Date‑ Signature:
Checklist for Student End of Lab Research Work
Student Name Degree Type
Date Research Began Data Research Ends
Research Mentor
Project Title
‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑
Waste and Safety Training
Date Initial Training: Dates renewal‑
Keys (Authorizing Personal Initial Receipt)
Room Date Received Date Returned
Room Date Received Date Returned
Room Date Received Date Returned
Room Date Received Date Returned
Final Research Report or Thesis Received
Desk and research area is clean
Glassware is clean and returned to storage
Equipment has been maintained (Inspect for leaking pumps, frayed electrical cords, dirty probes, proper response of test mixtures, etc.)
All reagents are returned to proper storage
Samples are labeled and prepared for storage
Waste has been fully labeled.
Notebooks and lose Data (Chromatographs, Spectra, etc.) labeled and turned in
Permanent address
Final grade authorization cleared
Waste description
Characteristic Hazardous Waste
D001 Ignitable waste‑A solid exhibits the characteristic of ignitability if a representative sample of the waste has any of the following properties: (1) It is a liquid, other than an aqueous solution containing less than 24 percent alcohol by volume and has a flash point less than 60oC(140oF) as determined by a Pensky‑Martens Closed Cup Tester, using the test method specified in ASTM Standard D‑93‑79 or D‑93‑80, or a Setaflash Closed C p Tester, using the method specified in ASTM Standard D‑3278‑78, or as determined by an equivalent test method approved by the Administrator under procedures set forth in 40 CFR Part 260. (2) It Is not a liquid and is capable, under standard temperature and pressure, of causing fire through friction, absorption of moisture or spontaneous chemical changes and, when ignited, burns so vigorously and persistently that it creates a hazard. (3) It is an ignitable compressed gas as defined in 49 CFR Part 173 and as determined by the test methods described in that regulation or equivalent test methods approved by the Administrator under 40 CFR Part 260. (4) It is an oxidizer as defined in 49 CFR Part 173.
D002 Corrosive waste‑A solid waste exhibits the characteristic of corrosivity if a representative sample of the waste has either of the following p rope ties: (1) It is aqueous and has a pH less than or equal to 2 or greater than or equal to 12.5, as determined by a pH meter using either an EPA test method or an equivalent test method approved by the Administrator under the procedures set forth in 40 CFR Part 260. (2) It is a liquid and corrodes steel (SAE 1020) AT A RATE GREATER THAN 6.35 MM (0.25 inch) per year at a test temperature of 55 C (130 F) as determined by the test method specified in NACE (National Association of Corrosion Engineers) Standard TM‑01069 or an equivalent test method approved by the Administrator under the procedures set forth in 40 CFR Part 260.
D003 Reactive waste: A solid waste exhibits the characteristic of reactivity if a representative sample of the waste has any of the following properties:
(1) It is normally unstable and readily undergoes violent change without detonating.
(2) It reacts violently with water.
(3) It ‑forms potentially explosive mixtures with water.
(4) When mixed with water, it generates toxic gases, vapors or fumes n a quantity sufficient to present a danger to human health or the environment.
(5) It is a cyanide or sulfide bearing waste which, when exposed to pH conditions between 2 and 12.5, can generate toxic gases, vapors or fumes in a quantity sufficient to present a danger to human health or the environment.
(6) It is capable of detonation or explosive decomposition or reaction at standard temperature and pressure.
(7) It is readily capable of detonation or explosive decomposition or reaction at standard temperature and pressure
(8) It is a forbidden explosive, a Class A explosive, or a Class B explosive as defined in 49 CFR Part 173.
EP Toxicity‑A solid waste exhibits the characteristic of EP toxicity if, sing the test methods described in 40 CFR Part 261 Appendix 11 or equivalent methods approved by the Administrator under the procedures set forth in 40 CFR Part 260, the extract from a representative sample of the waste contains any of the contaminants listed as D004 thru D017 at a concentration equal to or greater than the respective value given. Where the waste contains less than 0.5 percent filterable solids, the waste itself, after filtering, is considered to be the extract for the purposes of this section.
|
Code |
Description |
Maximum Concentration (mg/L) |
|
D004 |
Arsenic |
5.0 |
|
D005 |
Barium |
100.0 |
|
D006 |
Cadmium |
1.0 |
|
D007 |
Chromium |
5.0 |
|
D008 |
Lead |
5.0 |
|
D009 |
Mercury |
0.2 |
|
D010 |
Selenium |
1.0 |
|
D011 |
Silver |
5.0 |
|
D012 |
Endrin (1.2,3,4,10,10‑hexachloro‑1,7‑epoxy‑1,4,4a,5,6,7,8,8a‑octahydro‑ 1,4‑endo,(endo‑5,8‑dimethano‑naphthalene) |
0.02 |
|
D013 |
Lindane (1,2,3,4,5,6‑hexa‑chlorocyclohexane, gamma isomer) |
0.4 |
|
D014 |
Methoxychlor(1,1,1‑ trichloro2,2 bis[p‑rnethoxyphenyl]ethane) |
10.0 |
|
D015 |
Toxaphene (C10H10C8, technical chlorinated camphene, 67‑69 percent chlorine) |
0.5 |
|
D016 |
2,4‑D(2,4‑dichlorophenoxyacetic acid) |
10.0 |
|
D017 |
2,4,5‑TP Silvex (S2,4,5‑trichlorophenoxypropionic acid) |
1.0 |
Hazardous Waste from Nonspecific Sources
F001 The following spent halogenated solvents used in degreasing: tetrachloroethylene, trichlorethylene, methylene chloride, 1,1,1‑trichloroethane, carbon tetrachloride and chlorinated fluorocarbons and all spent solvent mixtures/blends used in degreasing containing, before use, a total of 10 percent or more (by volume) of one or more of the above halogenated solvents or those solvents listed in F002, F004, and F005; and still bottoms from the recovery of these spent solvents and spent solvent mixtures
F002 The following spent halogenated solvents: tetrachloroethylene, methylene chloride, trichloroethylene, 1,1,1‑tricliloroethane, chlorobenzene, 1,1,2-trichloro‑1,2,2‑trifluoroethane, ortho‑dichlorobenzene, trichlorofluoromethane, and 1,1,2, trichloroethane; all spent solvent mixtures/blends containing, before use, a total of 10 percent or more (by volume) of one or more of the above halogenated solvents or those solvents listed in F001, F004, and F005; and still bottoms from the recovery of these spent solvents and spent solvent mixtures.
Code Waste Description
F003 The following spent non-halogenated solvents: xylene, acetone, ethyl acetate, ethyl benzene, ethyl ether, methyl isobutyl ketone, n‑butyl alcohol, cyclohexanone, and methanol; all spent solvent mixtures/blends containing, before use, only the above spent non-halogenated solvents; and all spent solvent mixtures/blends containing, before use, one or more of the above non-halogenated solvents, and a total of 10 percent or more (by volume) of one or more of those solvents listed in F001, F002, F004, and FOOS; and still bottoms from the recovery of these spent solvents and spent solvent mixtures
F004 The following spent non-halogenated solvents: cresols and cresylic acid, and nitrobenzene; all spent solvent mixtures/blends containing before use a total 10 percent or more (by volume) of one or more of the above non-halogenated solvents or those spent listed in F001, F002, and FOOS; and still bottoms from the recovery of these spent solvents and spent solvent mixtures
F005 The following spent non-halogenated solvents: toluene, methyl ethyl ketone, carbon disulfide, isobutanol, pyridine, benzene, 2‑ethoxyethanol, and 2nitropropane; all spent solvent mixtures/blends containing, before use, a total of 10 percent or more (by volume) of one or more of the above non-halogenated solvents or those solvents listed in FOOL F002, or F004; and still bottoms from the recovery of these spent solvents and spent solvent mixtures
F006 Wastewater treatment sludge from electroplating operations except from the following processes: (1) Sulfuric acid anodizing of aluminum; (2) till plating on steel; (3) zinc plating (segregated basis) on carbon steel; (4) aluminum or zinc‑aluminum plating on carbon steel; (5) cleaning/stripping associated with tin, zinc, and aluminum plating on carbon steel; and (6) chemical etching and milling of aluminum
F007 Spent cyanide plating bath solutions from electroplating operations
F008 Plating bath residues from the bottom of plating baths from electroplating operations where cyanides are used in the process
F009 Spent stripping and cleaning bath solutions from electroplating operations were cyanides are used in the process.
F010 Quenching bath residues from oil baths from metal heat treating operations where cyanides are used in the process
F011 Spent cyanide solutions from salt bath pot cleaning from metal heat treating operations
F012 Quenching waste water treatment sludge from metal heat treating operations where cyanides are used in the process
F019 Wastewater treatment sludge from the chemical conversion coating of aluminum
F020 Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the production or manufacturing use (as a reactant, chemical intermediate or component in a formulating process) of tri‑ or tetrachlorophenol or of intermediates used to produce their pesticide derivatives. (This listing does not include wastes from the production (if hexachlorophene from highly purified 2,4,5‑trichlorophenot.)
Code Waste Description
F021 Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the production or manufacturing use (as a reactant, chemical intermediate or component in a formulating process) of pentachlorophenol, or of intermediates used to produce derivatives
F022 Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the manufacturing use (as a reactant, chemical intermediate, or component in a formulating process) of tetra‑, penta‑ or hexachlorobenzenes under alkaline conditions
F023 Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the production of materials on equipment previously used for the production or manufacturing use (as a reactant, chemical intermediate or component in a formulating process) of tri‑ and tetrachlorophenols. (This listing does not include wastes from equipment used only for the production or use of hexachlorophene from highly purified 2,4,5-trichlotophenol.)
F024 Wastes including but not limited to, distillation residues, heavy ends, tars, and reactor clean‑out wastes from the production of chlorinated aliphatic hydrocarbons, have carbon content from one to five, utilizing free radical catalyzed processes. (This listing does not include light ends, spent filters and filter aids, spent desiccants, wastewater, wastewater treatment sludge, spent catalysts, and "K" listed wastes‑Hazardous Wastes from Specific Sources.)
F026 Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the production of materials on equipment previously used for the manufacturing use (as a reactant, chemical intermediate, or component in a formulating process) of tetra‑, penta, or hexachlorobenzene under alkaline conditions
F027 Discarded unused formulations containing tri, tetra‑, or pentachlorophenol or discarded unused formulations containing compounds derived from these chlorophenols. (This listing does not include formulations containing hexachlorophene synthesized from prepurified 2,4,5‑trichlorophenol as the sole component.)
F028 Residues resulting from the incineration or thermal treatment of soil contaminated with EPA hazardous waste nos. F020, F021, F022, F023, F026, and F027
Discarded Commercial Chemical Products, Off Specification Species,
Container Residuals, and Spill Residues Thereof ‑ Acute Hazardous Waste
Code Waste Description
P023 Acetaldehyde, Chloro‑
P002 Acetamide, N-(aminothioxomethyl)‑
P057 Acetamide, 2‑fluoro‑
P058 Acetic acid, fluoro‑, sodium salt
P066 Acetimidic acid, N‑[(methylcarbamoyl) oxylthio‑, methyl ester
P002 1-Acetyl‑2‑thiourea
P003 Acrolein
P070 Aldicarb
P004 Aldrin
P005 Allyl alcohol
P006 Aluminum phosphide
P007 4‑alpha‑Aminopyridine
P009 Ammonium picrate
P119 Ammonium vanadate
P010 Arsenic acid
P012 Arsenic (III) oxide
P011 Arsenic (V) oxide
P011 Arsenic pentoxide
P012 Arsenic trioxide
P038 Arsine, diethyl
P036 Arsenous dichloride, phenyl‑
P054 Aziridine
P013 Barium cyanide
P024 Benzenamine, 4‑chloro‑
P077 Benzenamine, 4‑nitro‑
P028 Benzene, (chloromethyl)‑
P042 1,2‑Benzenediol, 4[1‑hydroxy ‑2-(methylamino)ethyl]-
P046 Benzeneethanamine, alpha, alpha-dimethyl-
P014 Benzenethiol
P001 2H‑1‑Benzopyran‑2‑one, 4-hydroxy‑3‑(3‑oxo‑l‑phenylbutyl)‑and salts
P028 Benzyl chloride
P015 Beryllium dust
P016 Bis(chloromethyl)ether
P017 Bromoacetone
P018 Brucine
P021 Calcium cyanide
P022 Carbon disulfide
P022 Carbon disulfide
P095 Carbonic dichloride
P023 Chloroacetaldehyde
P024 p‑Chloroaniline
P029 Copper cyanide
P030 Cyanides (soluble cyanide salts), not otherwise specified
P031 Cyanogen
P033 Cyanogen chloride
P034 2‑Cyclohexyl‑4,6‑dinitrophenol
P036 Dichlorophenylarsine
P037 Dieldrin
P038 Diethylarsine
P041 Diethyl‑p‑nitrophenyl phosphate
P040 O,O‑Diethyl O‑pyrazinylphosphorothioate
P043 Diisopropyl fluorophosphates (DEP)
P004 1,4,5,8‑Dimethanonaphthalene, 1,2,3,4,10,10‑hexachloro-1,4,4a,5,8,8a‑hexahydro-(1-alpha, 4-alpha. 4a-beta, 5-alpha, 8-alpha, 8a-beta)-
P060 1,4,5,8‑Dimethanonaphthalene, 1,2,3,4,10,10‑hexachloro-1,4,4a,5,8,8a‑hexahydro-(1-alpha, 4-alpha, 4a-beta, 5-beta, 8-beta, 8a-beta)-
P037 1,2,3,4,10,10-Hexahydro-6,7-epoxy-1,4,4a,5,6,7,8,8a-octahydro-endo,exo-1,4,5,8-demethanonaphthalene
P051 1,2,3,4,10,10-Hexahydro-6,7-epoxy-1,4,4a,5,6,7,8,8a-octahydro-endo,endo-1,4,5,8-demethanonaphthalene
P060 Hexachlorohexahydro-exo-exodemethanonaphthalene
P044 Dimethoate
P045 3,3‑Dimethyl‑1‑(methylthio)‑ 2-butanone, O-[(methylamino) carbonyloxime
P046 alpha,alpha‑Dimethylphenethylamine
P047 4,6‑Dinitro‑o‑cresol and salts
P048 2,4‑Dinitrophenol
P020 Dinoseb
P085 Diphosphoramide, octamethyl‑
P039 Disulfoton
P049 2,4‑Dithiobiuret
P050 Endosulfan
P088 Endothal
P051 Endrin
P042 Epinephrine
P101 Ethylcyanide
P054 Ethyleneimine
P097 Famphur
P056 Fluorine
P057 Fluoroacetamide
P058 Fluoroacetic acid, sodium salt
P065 Fulminic acid, mercury (2+) salt
P059 Heptachlor
P062 Hexaethyltetraphosphate
P116 Hydrazinecarbothioamide
P068 Hydrazine, methyl‑
P063 Hydrocyanic acid
P063 Hydrogen cyanide
P096 Hydrogen phosphide
P064 Isocyanic acid, methyl ester
P060 Isodrin
P007 3 (sH) ‑Isoxazolone, 5-(aminomethyl)‑
P092 Mercury, (acetato‑O) phenyl‑
P065 Mercury fulminate
P082 Methamine,N‑methyl‑N‑nitroso‑
P016 Methane, oxybis(chloro‑
P112 Methane, tetranitro‑
P118 Methanethiol, trichloro‑
P050 6,9‑Methano‑2,4,3-benzodioxathiepen,6,7,8,9 10,10-hexachloro‑1,5,5a,6,9,9a-hexahydro‑, 3-oxide
P059 4,7‑Methano‑ 1H-indene, 1,4,5.6,7,8,8‑heptachloro‑3a,4,7,7a‑ tetrahydro‑
P066 Methomyl
P067 2‑Methylaziridine
P068 Methyl hydrazine
P064 Methyl isocyanate
P069 2‑Methyllactonitrile
P071 Methyl parathion
P072 alpha‑Naphthylthiourea
P073 Nickel carbonyl
P073 Nicotine and salts
P076 Nitric oxide
P077 p‑Nitroanilinc
P078 Nitrogen dioxide
P076 Nitrogen oxide NO
P078 Nitrogen oxide N02
P081 Nitroglycerine
P082 N‑Nitrosodimethylamine
P084 N‑Nitrosomethylvinylamine
P074 Nickel cyanide
P085 Octamethy lpyrophosophoramide
P087 Osmium oxide
P087 Osmium tetroxide
P088 7‑Oxabicyclo [2.2.llheptane‑2,3-dicarboxylic acid
P089 Parathion
P034 Phenol, 2‑cyclohexyl‑4,6‑dinitro‑
P048 Phenol, 2,4‑dinitro
P047 Phenol, 2‑methyl‑4,6‑dinitro‑ and salts
P020 Phenol,2‑(I1‑methylpropyl)‑4,6-dinitro‑
P009 Phenol, 2,4,6‑trinitro‑, ammonium salt
P092 Phenylmercury acetate
P093 Phenylthiourea
P094 Phorate
P095 Phosgene
P096 Phosphine
P041 Phosphoric acid, diethyl 4-nitrophenyl ester
P039 Phosphorodithioic acid, O,O-diethyl S‑[2‑(ethylthio)ethyl] ester
P094 Phosphorodithioic acid, O,O-diethyl S‑[(ethylthio)methyl] ester
P044 Phosphorodithioic acid, O,O‑dimethyl S [2‑(methylamino)‑2‑Oxoethyl] ester
P043 Phosphorofluoric acid, bis(l-methylethyl)‑ester
P089 Phosphorothioic acid, O,O‑diethyl-O‑(4‑nitrophenyt) ester
P040 Phosphorothioic acid, O,O‑diethyl-O‑pyrazinyl ester
P097 Phosphorothioic acid, O‑[4-(dimethylamino)sulfonylphenyl] O,O‑dimethyl ester
P071 Phosphorothioic acid, O,O-dimethyl O‑(4‑nitrophenyl) ester
P110 Plumbane, tetraethyl‑
P098 Potassium cyanide
P099 Potassium silver cyanide
P070 Prop anal,2‑methyl‑2-(methylthio)‑, O‑[(methylamino)
Carbonyl]oxime
P101 Propanenitrile
P027 Propanenitrile,3‑chloro
P069 Propanenitrile, 2‑hydroxy‑2methyl
P081 1,2,3‑Propanetriol, trinitrate
P017 2-Propanone, 1‑bromo‑
P102 Propargyl alcohol
P003 2‑Propenal
P005 2‑Propen‑l‑ol
P067 1,2‑Propylenimine
P102 2‑Propyn‑l‑ol
P008 Pyridinamine
P075 Pyridine, (S)‑3‑(1-methyl‑2pyrrolidinyl)‑, and salts
P111 Pyrophosphoric acid, tetraethyl ester
P103 Selenourea
P104 Silver cyanide
P105 Sodium azide
P106 Sodium cyanide
P107 Strontium sulfide
P108 Strychnidin‑10‑one, and salts
P018 Strychnidin‑10‑one, 2,3 dimethoxy‑
P108 Strychnine and salts
P115 Sulfuric acid, thallium (I) salt
P109 Tetraethy1dithiopyrophosphate
P110 Tetraethyl lead
P111 Tetraethylpyrophosphate
P112 Tetranitromethane
P062 Tetraphosphoric acid, hexaethyl ester
P113 Thallic oxide
P113 Thallium (III) oxide
P114 Thallium (I) selenite
P115 Thallium (I) sulfate
P109 Thiodiphosphoric acid, tetraethyl ester
P045 Thiofanox
P049 Thioimidodicarbonic diazide
P014 Thiophenol
P116 Thiosemicarbazide
P026 Thiourea, (2‑chlorophenyl)‑
P076 Thiourea, 1‑naphthalenyl‑
P093 Thiourea, phenyl‑
P123 Toxaphene
P118 Trichloromethanethiol
P119 Vanadic acid, ammonium salt
P120 Vanadium (V) oxide
P084 Vinylamine, N‑methyl-nitroso‑
P001 Warfarin
P121 Zinc cyanide
P122 Zinc phosphide
Discarded Commercial Chemical Products, Off‑Specification Species,
U001 Acetaldehyde
U034 Acetaldehyde. trichloro‑
U187 Acetamide, N‑(4‑ethoxyphenyl)‑
U005 Acetamide, N‑914‑fluoren‑2‑yl
U112 Acetic acid, ethyl ester
U 144 Acetic acid, lead salt
U214 Acetic acid, thallium (1+) salt
U232 Acetic acid, (2,4,5-trichlorophenoxy)‑
U002 Acetone
U003 Acetonitrile
U004 Acetophenone
U005 2‑Acetylaminofluorene
U006 Acetyl chloride
U007 Acrylamide
U008 Acrylic acid
U009 Acrylonitrile
U011 Amitrole
U012 Aniline
U014 Auramine
U015 Azaserine
U010 Azirino(2', 3':3,4) pyrrolo-[1,2‑a]indole‑4,7‑dione, 6‑amino‑8-[((aminocarbonyl)ocy)methyl]-l,la,2,8,8a,8b‑hexahydro‑8a-methoxy‑5‑methyl‑
U157 Benz[j]aceanthrylene, 1,2-dihydro‑3‑methyl‑
U016 3,4‑Benzacridine
U017 Benzal chloride
U192 Benzamide, 3,5‑dichloro‑N‑(l,l-diethyl‑2‑propynyl)‑
U018 Benz[a]anthracene
U094 Benz[a] anthracene, 7,12‑d.imethyl‑
U012 Benzenamine
U014 Benzenamine,4,4'-carbonimidoyl-bis(N,N‑dimethyl-)
U049 Benzenamine, 4‑chloro‑2‑methyl‑
U093 Benzenamine,N,N‑dimethyl‑4-(phenylazo)‑
U328 Benzenamine, 2‑methyl‑
U353 Benzenamine, 4‑methyl‑
U158 Benzenamine, 4,4'‑methylenebis(2-chloro‑)
U222 Benzenamine, 2‑methyl‑, hydrochloride
U181 Benzenamine, 2‑methyl‑5-nitro
U019 Benzene
U038 Benzeneacetic acid, 4‑chloro-alpha‑(4‑chlorophenyl)‑alpha-hydroxy, ethyl ester
U030 Benzene, 1‑bromo‑4‑phenoxy‑
U035 Benzenebutanoic acid, 4‑[bis(2‑chloroethyl) amino]-
U037 Benzene, chloro‑
U221 Benzenediamine. ar‑methyl‑
U028 1,2‑Benzenedicarboxylic acid, bis (2‑ethylhexy) ester
U069 1,2‑Benzenedicarboxylic acid, dibutyl ester
U088 1,2‑Benzenedicarboxylic acid, diethyl ester
U102 1,2‑Benzenedicarboxylic acid, dimethyl ester
U107 1.2‑Benzenedicarboxylic acid, di‑n‑octyl ester
U070 Benzene, 1,2‑dichloro‑
U071 Benzene, 1,3‑dichloro‑
U072 Benzene, 1,4‑dichloro‑
U060 Benzene, 1,1'‑(2,2-dichloroethylidene)bis[4‑chloro‑
U017 Benzene, (dichloromethyl)‑
U223 Benzene, 1,3‑diisocyanatomethyl‑
U239 Benzene, dimethyl‑
U201 1,3‑Benzenediol
U127 Benzene, hexachloro‑
U056 Benzene, hexahydro‑
U220 Benzene, methyl‑
U105 Benzene, 1‑methyl‑2,4‑dinitro‑
U106 Benzene, 2‑methyl‑1,3‑dinitro‑
U055 Benzene, (1‑methylethyl)‑
U169 Benzene, nitro‑
U183 Benzene, pentachloro‑
U185 Benzene, pentachloronitro‑
U020 Benzenesulfonic acid choride
U020 Benzenesulfonyl chloride
U207 Benzene, 1,2,4,5‑tetrachloro-
U061 Benzene, 1,1'‑(2,2,2-trichloroethylidene)bis[4‑chloro-
U247 Benzene, 1,1'‑(2.2,2-trichloroethylidene)[4‑ethoxy‑
U023 Benzene, (trichloromethyl)‑
U234 Benzene, 1,3,5‑trinitro‑
U021 Benzidine
U202 1,2‑Benzisothiazol‑3‑(2H) one,1,1-dioxide and salts
U203 1,3‑Benzodioxole, 5‑(2‑propenyl)‑
U141 1,3‑Benzodioxole, 5‑(l‑propenyl)‑
U090 1,3‑Benzodioxole, 5‑propyl
U064 Benzo[rst]pentaphene
U022 Benzo[a]pyrene
U197 p‑Benzoquinone
U023 Benzotrichloride
U085 2,2'‑Bioxirane
U021 (l,l'Biphenyl)-4,4'diamine
U073 (1,1'-Biphenyl)‑4,4'-diamine, 3,3-dichloro-
U091 (1,1'‑Biphenyl)‑4,4'‑diamine, 3,3'-dimethoxy-
U095 (1,1'‑Biphenyl)-4,4'‑diamine, 3.3'-dimethyl‑
U027 Bis(2‑chloroisopropyl)ether
U024 Bis(2‑chloromethoxy)ethane
U028 Bis(2‑ethylhexyl)phthalate
U225 Bromoform
U030 4‑Bromophenyl phenyl ether
U128 1,3‑Butadiene, 1,1,2,3,4,4‑hexachloro‑
U172 1,Butanamine, N‑butyl‑N‑nitroso‑
U031 1‑Butanol
U159 2‑Butanone
U160 2‑Butanone peroxide
U053 2‑Butenal
U074 2‑Butene, 1,4‑dichloro‑
U143 2‑Butenoic acid, 2‑methyl‑, 7‑[(2,3-dihydroxy‑2‑(1‑methoxyethyl)‑3‑methyl‑l‑oxobutoxy) methyl-12,3,5,7 a‑tetrahydro-1-pyrrolizin‑1‑yl ester, [1S‑[alpha (Z),7(2S, 3R),7aa;‑Pha])‑
U031 n‑Butyl alcohol
U136 Cacodylic acid
U032 Calcium chromate
U238 Carbamic acid, ethyl ester
U178 Carbamic acid, imethylnitroso‑, ethyl ester
U097 Carbamic chloride, dimethyl‑
U114 Carbamodithioic acid, 1,2-ethanediylbis‑, salts and esters
U062 Carbamothioic acid, bis(l-methylethyl)‑S‑(2.3‑dichoro‑2-propenyl) ester
U215 Carbonic acid, dithallium(1+) salt
U033 Carbonic difluoride
U156 Carbonochloridic acid, methyl ester
U033 Carbon oxyfluoride
U211 Carbon tetrachloride
U034 Chloral
U035 Chlorambucil.
U036 Chlordane
U026 Chlornaphazine
U037 Chlorobenzene
U039 p‑Chloro‑m‑cresol
U041 I‑Chloro‑2,3‑epoxypropane
U042 2‑Chloroethyl vinyl ether
U044 Chloroform
U046 Chloromethyl methyl ether
U047 beta‑Chloronaphthalene
U048 o‑Chlorophenol
U049 4‑Chloro‑o‑toluidine, hydrochloride
U032 Chromic acid, calcium salt
U050 Chrysene
U051 Creosote
U052 Cresole (Cresylic acid)
U053 Crotonaldehyde
U055 Cumene
U246 Cyanogen bromide
U197 2,5‑Cyclohexadiene‑1, 4‑dione
U056 Cyclohexane
U057 Cyclohexanone
U130 1,3‑Cyclopentadiene, 1,2,3,4,5,5-hexachloro-
U058 Cyclophosphamide
U240 2.4‑D, salts and esters
U059 Daunomycin
U060 DDD
U061 DDT
U062 Diallate,
U063 Dibenz[a,h]anthracene
U064 Dibenzo[a,i]pytene
U066 1,2‑Dibromo‑3‑chloropropane
U069 Dibutyl phthalate
U070 o‑Dichlorobenzene
U071 m‑Dichlorobenzene,
U072 p‑Dichlorobenzene
U073 3,3'‑Dichlorobenzidine
U074 1,4‑Dichloro‑2‑butene
U075 Dichlorodifluoromethane
U078 1,1‑Dichloroethylene
U079 1,2‑Dichloroethylene
U025 Dichloroethyl ether
U081 2,4‑Dichlorophenol
U082 2,6‑Dichlorophenol
U240 2,4‑ Dichlorophenoxy acetic acid salts and esters
U083 1,2‑Dichloropropane
U084 1,3‑Dichloropropene
U085 1,2:3,4‑Diepoxybutane
U108 1,4‑Diethyleneoxide
U086 N,N‑Diethylhydrazine
U087 O,O‑Diethyl‑S‑methyl-dithiophosphate
U088 Diethyl phthalate
U089 Diethylstilbestrol
U090 Dihydrosafrole
U091 3,3'‑Dimethoxybenzidine
U092 Dimethylamine
U093 Dimethylaminoazobenzene
U094 7,12‑Dimethylbenz[a]anthracene
U095 3,3'‑Dimethylbenzidine
U096 alpha,alpha-Dimethylbenzylhydroperoxide
U097 Dimethylcarbamoyl chloride
U098 1,1‑Dimethylhydrazine
U099 1,2‑ Dimethylhydrazine
U101 2,4‑Dimethylphenol
U102 Dimethyl phthalate
U103 Dimethyl sulfate
U105 2,4‑Dinitrotoluene
U106 2,6‑Dinitrotoluene
U107 Di‑n‑octyl phthalate
U108 1,4‑Dioxane
U109 1,2‑Diphenylhydrazine
U110 Dipropylamine
U111 Di‑n‑propyinitrosamine
U001 Ethanal
U174 Ethanamine, N‑ethyl‑N‑nitroso‑
U155 1,2‑Ethanediamine, N,N‑dimethyl-N'‑(2‑thienylmethyl)‑
U067 Ethane, 1,2‑dibromo‑
U076 Ethane, 1.1‑dichloro‑
U077 Ethane, 1,2‑dichloro‑
U131 Ethane, hexachloro‑
U024 Ethane, 1, 1'-[methylenebis(oxy)]bis [2‑chloro-
U117 Ethane, 1,1'‑oxybis‑
U025 Ethane, 1,1'‑oxybis[2‑chloro‑
U184 Ethane, pentachloro‑
U208 Ethane, 1,1,1,2‑tetrachloro
U209 Ethane, 1, 1,2,2‑tetrachloro
U218 Ethanethioamide
U227 Ethanol, 2‑ethoxy‑
U359 Ethane, 1, 1,2‑trichloro‑
U173 Ethanol, 2,2'‑(nitrosoimino)bis‑
U004 Ethanone, 1‑phenyl‑
U043 Ethene, chloro‑
U042 Ethene, (2‑chloroethoxy)‑
U078 Ethene, 1,1‑dichloro‑
U079 Ethene, 1,2‑dichloro‑,(E)‑
U210 Ethene, tetrachloro
U228 Ethene, trichloro
U112 Ethyl acetate
U113 Ethyl acrylate
U238 Ethyl carbamate
U038 Ethyl 4,4'‑dichlorobenzilate
U114 Ethylenebisdithiocarbamic acid, salts and esters
U067 Ethylene dibromide
U077 Ethylene dichloride
U359 Ethylene glycol monoethylether
U115 Ethylene oxide
U116 Ethylene thiourea
U117 Ethyl ether
U076 Ethylidene dichloride
U118 Ethyl methacrylate
U119 Ethylmethanesulfonate
U120 Fluoranthene
U122 Formaldehyde
U123 Formic acid
U124 Furan
U125 2‑Furancarboxaldehyde
U147 2,5‑Furandione
U213 Furan, tetrahydro‑
U125 Furfural
U124 Furfuran
U206 D‑Glucopyranose, 2‑deoxy‑2(3-methyl‑3‑nitrosourcido)‑
U126 Glycidylaldehyde
U163 Guanidine, N‑methyl‑N'‑nitro‑N-nitroso‑
U127 Hexachlorobenzene
U128 Hexachlorobutadiene
U129 Hexachlorocyclohexane(gamma isomer)
U130 Hexachlorocyclopentadiene
U131 Hexachloroethane
U132 Hexachlorphene
U243 14exachloropropene
U133 Hydrazine
U086 Hydrazine, 1,2‑diethyl‑
U098 Hydrazine, 1, 1 ‑dimethyl‑
U099 Hydrazine, 1,2,‑dimethyl
U109 Hydrazine, 1,2 ‑diphenyl
U134 Hydrofluoric acid
U 134 Hydrogen fluoride
U135 Hydrogen sulfide
U096 Hydroperoxide,l‑methyl‑l-phenylethyl‑
U136 Hydroxydimethylarsine xide
U116 2‑Imidazolidinethione
U137 Indeno[1,2,3-cd]pyrene
U139 Iron dextran
U190 1,3‑Isobenzofurandione
U140 Isobutyl alcohol
U141 Isosafrole
U142 Kepone
U143 Lasiocarpine
U144 Lead acetate
U146 Lead, bis(acetate-O)tetrahydroxytri‑
U145 Lead phosphate
U146 Lead subacetate
U129 Lindane
U147 Maleic anhydride
U148 Maleic hydrazide
U149 Malonitrile
U150 Melphalan
U151 Mercury
U152 Methacrylonitrile
U092 Methanamine, N‑methyl‑
U029 Methane, bromo‑
U045 Methane, chloro‑
U046 Methane, chloromethoxy‑
U068 Methane, dibromo‑
U080 Methane, dichloro‑
U075 Methane, dichlorodifluoro‑
U138 Methane, iodo‑
U119 Methanesulfonic acid, ethyl ester
U211 Methane, tetrachloro‑
U153 Methanethiol
U225 Methane, tribromo‑
U044 Methane, trichloro‑
U121 Methane, trichlorofluoro‑
U123 Methanoic acid
U154 Methanol
U155 Methapyrilene
U142 1,3,4‑Metheno‑2H-cyclobutal[cd]pentalen-2‑one, l,la,3,3a,4,5,5a,5b,6-decachlorooctahydro‑
U247 Methoxychlor
U154 Methyl alcohol
U029 Methyl bromide
U186 1-Methylbutadiene
U045 Methyl chloride
U156 Methylchlorocarbonate
U226 Methylchloroform
U157 3‑Methylcholanthrene
U158 4,4'‑Methylenebis(2-chloroaniline)
U068 Methylene bromide
U080 Methylene chloride
U159 Methyl ethyl ketone
U160 Methyl ethyl ketone peroxide
U138 Methyl iodide
U161 Methyl isobutyl ketone
U162 N‑Methyl‑N'‑nitro‑N‑nitrosoguanidine
U161 4‑Methyl‑2‑pentanone
U164 Methylthiouracil
U010 Mitomycin C
U059 5,12‑Naphthacenedione, (8S‑cis)-8-acetyl-10-[(3‑amino‑2,3,6-trideoxy)-alpha-L-Iyxo-hexopyranosyl)oxyl]-7,8,9 10-tetrahydro-6,8,11-trihydroxy-1-methoxy‑
U165 Naphthalene
U047 Naphthalene, 2‑chloro‑
U166 1,4‑Naphthalenedione
U236 2,7‑Naphthatenedisulfonic acid, 3,3'‑dimethyl‑(1,I'-biphenyl)‑4,4' diyl)]-bis(azo)bis(S‑amino-4-hydroxy)-, tetrasodium salt
U166 1,4‑Naphthoquinone
U167 alpha‑Naphthylamine
U168 beta‑ Naphthylamine
U026 2‑Naphthylamine, N,N'‑bis (2‑chloromethyl)‑
U167 I‑Naphthylenamine
U168 2‑Naphthylenamine
U217 Nitric acid, thallium(l+) salt
U169 Nitrobenzene
U170 p‑Nitrophenol
U171 2‑Nitropropane
U172 N–Nitrosodi-n‑butylamine
U173 N‑Nitrosodiethanolamine
U 174 N-Nitrosodiethylamine
U176 N‑Nitroso‑N‑ethylurea
U 177 N‑Nitroso‑N‑methylurea
U179 N-Nitroso-N‑methylurethane
U179 N‑Nitrosopiperidine
U180 N‑Nitrosopyrrolidine
U181 5‑Nitro‑o‑toluidine
U193 1,2‑Oxathiolane,2,2‑dioxide
U058 2H-1,3,2‑Oxazaphosphorin-2-amine,N,N‑bis(2‑chloroethyl)tetrahydro-, 2‑oxide
U115 Oxirane
U126 Oxiranecarboxyaldehyde
U041 Oxirane, (chloromethyl)‑
U182 ParaLdehyde
U183 Pentachlorobenzene
U184 Pentachloroethane
U185 Pentachloronitrobenzene (PCNB)
U242 Pentachlorophenol
U186 1,3‑Pentadiene
U187 Phenacetin
U188 Phenol
U048 Phenol, 2‑chloro‑
U039 Phenol, 4‑chloro‑3‑methyl‑
U081 Phenol,2,4‑dicliloro‑
U082 Plienol,2,6‑dichloro‑
U089 Phenol,4.4'‑(1,2‑diethyl‑ 1,2-ethenediyl)bis‑, (E)‑
U101 Phenol,2,4‑dimethyl‑
U052 Phenol, methyl‑
U132 Phenol,2,2'‑methylenebis[ 3,4,6-trichloro‑
U170 Phenol, 4‑nitro-
U242 Phenol, Pentachloro‑
U212 Phenol, 2,3,4,5‑tctrachloro
U230 Phenol, 2,4,5‑trichloro‑
U231 Phenol,2,4,6‑trichloro‑
U150 L‑Phenylalanine,4‑[bis(2-chloroethyl)amino]‑
U145 Phosphoric acid, lead salt
U087 Phosphorodithioic acid, O,O-diethyl‑, S‑methyl‑, ester
U189 Phosphorous sulfide
U190 Phthalic anhydride
U191 2‑Picoline
U179 Piperidine, 1‑nitroso‑
U192 Pronamide
U 194 1‑Propanamine
U111 1-Propanamine, N‑nitroso‑N‑N-propyl‑
U101 1‑Propanamine, N‑propyl‑
U066 Propane, 1,2‑dibromo‑3‑chloro‑
U149 Propanedinitrile
U171 Propane,2‑nitro‑
U027 Propane,2,2'‑oxybis[2‑chloro‑
U193 1,3‑Propane sultone
U235 1-Propanol,2,3‑dibromo‑, phosphate (3:1)
U140 1‑Propanol, 2‑methyl‑
U002 2‑Propanone
U084 1‑Propane, 1,3‑dichloro‑
U152 2‑Propanenitrile,2‑methyl‑
U007 2‑Propenamide
U243 1-Propene, hexachloro‑
U009 2‑Propenenitrile
U008 2‑Propenoic acid
U113 2‑Propenoic acid, ethyl ester
U118 2‑Propenioc acid, 2‑methyl-, ethyl ester
U162 2‑Propenoic acid, 2‑methyl-, methyl ester
U233 Propionic acid, 2‑(2,4,5-trichlorophenoxy)‑
U194 n‑Propylamine
U083 Propylene dichloride
U148 3.6‑Pyridazinedione, 1,2‑dihydro‑
U196 Pyridine
U191 Pyridine, 2‑methyl‑
U237 2,4(l H,3H)‑Pyrimidinedine,5- [bis(2‑chloroethyl)amino]
U164 4‑(1 H)‑Pyrimidinone, 2,3 dihydro-6‑methyl‑2‑thioxo‑
U180 Pyrrolidine, 1‑nitroso‑
U200 Reserpine
U201 Resorcinol
U202 Saccharin and salts
U203 Safrole
U204 Selenious acid
U204 Selenium dioxide
U205 Selenium sulfide
U015 L‑Serine, diazoacetate (ester)
U233 Silvex
U206 Streptozotocin
U103 Sulfuric acid, dimethyl ester
U189 Sulfur phosphide
U232 2,4,5‑T
U207 1,2,4,5‑Tetrachlorobenzene
U208 1,1,1,2‑Tetrachloroethane
U209 1,1,2,2‑Tetrachloroethane
U210 Tetrachloroethylene
U212 2,3,4,6‑Tetrachlorophenol
U213 Tetrahydrofuran
U214 Thallium(l) acetate
U215 Thallium(l) carbonate
U216 Thallium chloride
U217 Thallium(l) nitrate
U218 Thioacetamide
U153 Thiomethanol
U244 Thioperoxydicarbonic diamide, tetramethyl‑
U219 Thiourea
U244 Thiuram
U220 Toluene
U221 Toluenediamine
U223 Toluene diisocyanate
U328 o‑Toluidine
U353 p‑Toluidine
U222 o‑Toluidine hydrochloride
U011 1H‑1,2,4‑Triazol‑3‑amine
U226 1, 1, 1‑Trichloroethane
U227 1, 1,2‑Trichlorethane
U228 Trichloroethylene
U121 Trichloromonofluoromethane
U230 2,4,5‑Trichlorophenol
U231 2,4,6‑Trichlorophenol
U234 sym‑Trinitrobenzene
U182 1,3,5‑Trioxane,2,4,6‑trimethyl‑
U235 Tris(2,3‑dibromopropyl) phosphate
U236 Trypan blue
U237 Uracil mustard
U176 Urea, N‑ethyl‑N‑nitroso‑
U177 Urea, N‑methyl‑N‑nitroso
U043 Vinyl chloride
U248 Warfarin, when present in concentrations of 0.3% or less
U239 Xylene
U200 Yohimban‑16‑carboxylic acid, 11, 17‑dimethoxy-18-[(3,4,5-trimethoxybenzoyl)oxy]-, methyl ester
U249 Zinc phosphide, when present at concentrations of 10% or less